Category: EMF Filters/Dirty Electricity/Clean Energy

EMF Filter

Stetzerizer Filters

See our store for products and details.  Availability varies.  See many of our EMF Protection products at the online store.  Demand is high.  https://thebraincan.com/store-2/

 

EMF Filter
EMF Filter

 

Stetzerizer Filters – Additional Installation Notes

 

  1. For best results, make sure you turn your electronic devices ON during filter installation – especially televisions and computers.
  2. Install two (2) Stetzerizer filters where each computer and each television in the home is located. If you have Plasma TV’s you will need to install three (3) filters where each of those is located. You will likely need power strips and/or tri-tap adapters (electrical tees) in order to accommodate the filters. Installing filters in these locations first will lower readings throughout the house and should result in using fewer filters overall. Then move on to testing with the Microsurge meter and finishing the install.
  3. After Step 2 has been completed, pick an outlet to start testing with the Microsurge meter – we usually start in a bedroom. Plug in the Microsurge meter and note the number on the LCD display (expressed in GS units). Plug in 1 Stetzerizer filter to the same outlet and note the number on the meter again.
  4. 4. If you see a reduction in GS unit readings of 20% or more, leave the filter in that outlet and unplug the meter. Move on to the next outlet and repeat the same process.
  5. If you did not see a reduction of 20% or more, remove the filter and the meter – you do not need a filter at that particular outlet. Move on to the next outlet and repeat the same process.
  6. Continue these steps until you have tested every outlet in your home – including the garage and basement, but excluding outdoor outlets – and installed filters where they are needed. The average house needs about 20 Stetzerizer filters – you may need more if you have more electronic devices in your home.
  7. Note: Save the kitchen for last; there are normally fewer outlets in the kitchen, so having them filled with filters is inconvenient. There are also other problems that can present themselves in the kitchen, or even in other rooms of the home. The most common thing we see is outlets having a shared neutral wire; steps to resolve this issue follow:
  1. Say you are testing an outlet and you have the Microsurge meter plugged into the bottom half of the receptacle. Normally you would plug in a Stetzerizer filter to the top half of the receptacle and the GS unit reading on the meter would decrease. However, at this outlet you find that when you plug in the filter the meter reading increases; this indicates a shared neutral.
  2. To properly filter this outlet, you’ll need 2 powerstrips or electrical tees. Plug one powerstrip into the top of the receptacle, and another into the bottom receptacle.
  3. Plug the Microsurge meter into one of the powerstrips and note the GS unit reading. Then plug a filter into that same powerstrip – you should see the GS unit reading decrease this time. Repeat this process in the other powerstrip.
  4. You’ll end up with a powerstrip and a filter plugged into both the top and bottom halves of the receptacle, and your shared neutral problem is solved.
  1. Another thing to look out for is switched outlets – outlets controlled by a light switch. These are most common in the living room, but other rooms may have them as well. Be sure that you do not install Stetzerizer filters in the “switched” portion of a switched outlet, as turning the outlet off would effectively remove the filter from your installation.
  2. Once this process has been followed you should be able to go back to any outlet in your home and see GS readings of 50 or less (35 or less is ideal).

 

Testing for “bad” light bulbs

1) Tools needed: floor or desk lamp, Stetzerizer Microsurge meter

2) Install the light bulb you wish to test in the floor or desk lamp, and plug the lamp into an outlet.

3) Plug the Microsurge meter into the same outlet and note the GS unit reading on the display.

4) Turn the floor/desk lamp on and note the GS unit reading again. If it increased by more than a few points, the light bulb is a generator of dirty electricity – you don’t want to use it in your home.

 

Technical Information and Downloads:
Health Effects of EMF Health Effects

Contact:  Sales@PHDService.com

See our store for products and details.  Availability varies.  See many of our EMF Protection products at the online store.  Demand is high.  https://thebraincan.com/store-2/

 

EMF Filter

Dirty Electricity Library/ Electromagnetic Frequency Library

www.EMFFix.com and www.TheBrainCan.com present a media library of presentations on EMF, EMF Reconciliation, EMF Filtration, EMF Meter and Measurement, Electromagnetic Frequency, and EMF Filters.  We offer opportunities for customers to purchase these units, for people to secure an income helping others, or both.  See the opportunity link at the bottom of the page.

See our store for products and details.  Availability varies.  See many of our EMF Protection products at the online store.  Demand is high.  https://thebraincan.com/store-2/

 

 

 

 

 

 

 

 

 

 

 

 

Health Hazards of Electromagnetic Radiation
by Bruce Fife, ND

A Startling Look At The Effects Of Electropolution On Your Health. Edited and compiled by Bruce Fife, N.D. with the assistance of the Electric and Magnetic Fields Research and Public Information Dissemination Program and the National Institute of Environmental Health Sciences.

Includes A New Chapter on Cell Phones!! New Second Edition

We are under continual attack from electromagnetic fields (EMFs) radiating from power lines, household wiring, microwave ovens, computers, televisions, clock radios, cellular phones, electric blankets and other appliances. Researchers have correlated electropollution with increases in cancer, birth defects, depression, learning disabilities, Chronic Fatigue Syndrome, Alzheimer’s disease, and Sudden Infant Death Syndrome. The danger is real and with increasing use of electricity in our environment it is one of the reasons why many scientists believe some disease rates are on the rise.

EMFs are not blocked or weakened by trees, walls, buildings, or other structures. Like X-rays they pass through these objects and into our bodies — disrupting normal cellular function and biological processes.

For most of us our greatest exposure to EMFs comes from within our own homes. All household appliances emit EMFs. But you cannot tell which are most dangerous by their size or function. Often the small devices like electric can openers and hair dryers are much more dangerous than the larger ones such as electric ovens or refrigerators.

In this book you will find out —
*About the dangers you face with EMF exposure
*Why certain diseases persist in spite of medical treatment
*How to reduce exposure from computer and TV screens
*If microwave ovens are safe or not
*What home appliances are the most dangerous
*Where we get the most exposure <.LI>
*How to find hidden EMF “hot spots” in the home
*What you can do to protect yourself and your family

Technical Information and Downloads:
Health Effects of EMF Health Effects

Contact:  Sales@PHDService.com

See our store for products and details.  Availability varies.  See many of our EMF Protection products at the online store.  Demand is high.  https://thebraincan.com/store-2/

Ted's Girl

Dirty Electricity in Schools and Health Effects

Dirty Power and Healthy Schools is it Possible? What do dairy cows and students have in common?

See our store for products and details.  Availability varies.  See many of our EMF Protection products at the online store.  Demand is high.  https://thebraincan.com/store-2/

 

Magda Havas, Ph.D., Environmental & Resource Studies Program at Trent University.

 

Last January I received a phone call from Michelle Illiatovitch in Toronto who told me that both she and her daughter, Kestra, were electrically sensitive. Shortly after some renovations Kestra began to feel ill. She noticed that the lights in her bedroom were flickering so they called in an electrician who corrected the problem that related to the loose wires in the fuse box. Kestra’s health improved dramatically but she still felt tired and had frequent, headaches, fuzzy thinking, depression, chest pain and nausea.

 

Michelle’s niece, Catherine, developed chronic fatigue shortly after moving to a farm in Wisconsin. She read that some farmers in her area were experiencing health problems and they were also having difficulty with their dairy herds and that Dave was helping the farmers solve their problems, which were electricity-related.

 

She contacted Mr. David who told her to turn the power off in her home. She did this and began to feel better almost immediately. She then purchased some of his equipment to measure her home and to filter out the dirty electricity. Shortly after installing the electric filters, also known as capacitors, her health began to improve. She was so impressed she contacted her Aunt Michelle to share the good news.

 

Michelle also bought some filters, which plug into an electrical outlet, and installed them in her home. Not only did her health improve but the health of everyone improved including her dog and her husband.

 

Kestra was feeling much better at home but when she went to school she became ill again. Michelle asked the school principal if she could install some filters in the school to help her daughter. Joy Kurtz, the Principal of Willow Wood School agreed.

That’s when Michelle phoned me.

 

She wondered if I would do a study to determine the effectiveness of these filters. I was familiar with electrical-sensitivity but it was my understanding that a very small percentage of our population is likely to be electrically-sensitive and because the symptoms are so vague it’s difficult to know if it’s indeed electrical-sensitivity or something else that’s causing the problem.

 

The symptoms for sensitivity vary. Some develop headaches when they go shopping in stores that have bright halogen lights. Others become tired or can’t think clearly. Some develop skin rashes after using a computer. In severe situations people can even loose consciousness. Generally those with electrical sensitivity prefer incandescent lighting to fluorescent lighting.

 

I was skeptical this study would show anything partly because I was skeptical about the effectiveness of the filters and partly because I felt the population of teachers and students was too small. But I was also intrigued and agreed to design a questionnaire.

 

No one in the school, apart from the Principal and the head Custodian, knew what we were doing. It was necessary to keep the teachers in the dark initially so that psychological bias would not play a role in the answers they provided. This is referred to as a “blind” experiment.

 

We measured the electromagnetic environment in the school with and without the filters. The filters removed many of the microsurges on the electrical wiring in the school but did not change the electric or magnetic fields, which were already low. These microsurges consist of high frequency energy on an electrical wire and are generated by various appliances and equipment.

 

At the end of the study that lasted 6 weeks, 3 weeks without and 3 weeks with the filters, I received several boxes of completed questionnaires. The real work began.

 

I analyzed the teacher results first and was amazed by what I found. Of the more than 40 teachers, 26 responded regularly. Of these 26, 4 did not change, 4 were slightly worse and 18 improved while the filters were installed. In decreasing order of magnitude this is what we found. While the filters were installed, 46% of the teachers experienced less fatigue, 42% were less frustrated, 35% were more satisfied with their work, 35% had a greater sense of “well-being”, 27% were less irritable, 23% had more energy, 23% experienced less body pain, and 19% had fewer headaches. And all of this occurred during February, a month we normally associate with the “blahs.”

 

Preliminary analysis of the student results shows that both high school and elementary students improved more during the afternoon than in the morning. In elementary school, student disruptions were reduced by an average of 3 to 4 minutes per class, which allows more teaching time. The high school results were less conclusive.

 

While the results are encouraging and suggest that these filters can improve the school environment, it’s necessary to repeat this study at other schools to see if the results are consistent. If they prove to be consistent then we may now have a tool to improve our electrical environment at home and at work. Just as we have air filters to remove airborne particulates and water filters to remove chemicals in our drinking water, Dave has designed a filter that reduces indoor electrical pollution associated with electronic devices like computers and variable speed motors.

 

At a recent talk at Willow Wood School in Toronto, Mr. David said this filter would even reduce some of the microsurges entering your home from your neighbor next-door. His work on dairy farms in Wisconsin resulted in healthier cows and higher milk yields. While these filters are not the answer to all of our electrical problems, they may make living more tolerable for the small percentage of the population who are truly electrically-

sensitive and, if our results are correct, they may improve the quality of life even for those of us who aren’t.

EMF Filter
EMF Filter

 

Technical Information and Downloads:
Health Effects of EMF Health Effects

Contact:  Sales@PHDService.com

See our store for products and details.  Availability varies.  See many of our EMF Protection products at the online store.  Demand is high.  https://thebraincan.com/store-2/

EMF Filter

EMF Microsurge Meter/ Dirty Electricity Meter/ EMF Meter/EMF Filter System

EMF FILTERS (EMI Filters) www.EMFFix.com

See our store for products and details.  Availability varies.  See many of our EMF Protection products at the online store.  Demand is high.  https://thebraincan.com/store-2/

EMF Microsurge Meters

 

Contact Info:

Office: 850-685-2353

email: sales@EMFfix.com

 

Designed to measure home and office Power Quality

 

Microsurge Meter Operating Instructions

 

The intellectual property behind the Microsurge meter belongs to the individual who conceived and designed the meter: Professor Martin Graham. The Microsurge meter:

  • Works for 60 Hz/120 Volt North American and 50 Hz/240 A.C. Volt European systems.
  • LCD display reads the Volts per second present, which is an approximation for the high frequency energy. High frequencies are the frequencies which are most harmful to equipment, animals, and humans.
  • The good, marginal, and undesirable range of meter readings are conveniently listed on the back of the Microsurge meter.

 

Electrosensitive people have reported sensitivities with readings as low as 27 on the Microsurge meter. However, medium or even low Microsurge meter readings should not be interpreted as a guarantee that there is no harmful health impact; only a medical expert can determine that. Caution is required. Some harmful health effects of high frequency energy on humans appear to be cumulative, and possibly non-reversible. Science is inconclusive in this area, although the body of empirical evidence available for guidance continues to expand and stabilize.

 

Microsurge Meter Design Criteria

 

Microsurge meters were specifically designed as a companion to the EMF FILTERS. The meters measure the level of harmful electromagnetic “energy” present, and their primary use is to guide effective filter installation.

EMF Filter
EMF Filter

Microsurge meters are low cost, robust, and easy to use by non-technical people. The meters were designed to measure harmonics and other high frequency “energy” present, which are the frequencies most detrimental to human health. The meters effectively ignore the effects of 60 Hz power and other lower, less harmful frequencies. Specifically, the meter measures the average magnitude of the changing voltage as a function of time (dV/dt), which naturally emphasizes transients and other high frequency phenomena that change rapidly with time. The measurements of dV/dt read by the meter are defined as G-S (Graham-EMF Filters) units (since no standard term is available). The G-S units are a measure of “harmful energy” which is a function of frequency, or more generally, rate of change of voltage or dV/dt.

 

Using the Microsurge Meter for a Typical Home Installation

 

Microsurge meters measure the levels of safe, borderline, or dangerous levels of “energy” present. These levels are conveniently shown on the back of the meter for reference. These levels have been developed through research (much of it in Russia and neighboring countries) and confirmed by experience in North America. The levels have been adopted by the Sanitary Stations (Health Departments) of the Republic of Kazakhstan.

 

Starting from points that typically have the highest readings such as the power input panel, computers, and televisions, the meter is used to measure the initial levels of G-S energy and reduction as filters are added. Once the G-S levels are acceptable at one location, the process should be repeated at the next location. After the installation of the filters is complete, a final confirmation of the G-S levels should be performed throughout the house.

 

 

 

Meter Characteristics

  • 1 in. x 2.75 in. x 4.25 in.
  • Encased in an off-white plastic covering that fits naturally with home or office decor
  • Certified by the Government of Kazakhstan as the official means of measuring RF Energy on building wires
  • Simply plug into a normal electrical outlet to use
Technical Information and Downloads:
Health Effects of EMF Health Effects

Contact:  Sales@PHDService.com

See our store for products and details.  Availability varies.  See many of our EMF Protection products at the online store.  Demand is high.  https://thebraincan.com/store-2/

 

EMF Filter

EMF Filter Technical Information (Dirty Electricity to Clean Energy)

EMF FILTERS (EMI Filters) from EMFFix.com

See our store for products and details.  Availability varies.  See many of our EMF Protection products at the online store.  Demand is high.  https://thebraincan.com/store-2/

EMF Filter Technical Information (Dirty Electricity to Clean Energy)

EMF FILTERS (EMI Filters)- For Home and Office

EMF Filter
EMF Filter

Contact Info:

Office: 850-685-2353

email: sales@EMFFix.com

Email is the preferred method of contact so that we adequately understand and address all of your questions and concerns.

 

A new application of existing science and technology designed to improve power quality in home and office environments.

 

System Overview

 

The EMF FILTERS filter is based upon 100 year-old science and power engineering principles. Newly introduced is the design, which is focused on the needs of the customers in homes, offices, schools, etc. Filters have been extensively applied for decades by industrial users and the electric utility industry itself. The EMF FILTERS filter is designed to filter harmonics and other high frequency current (trash) from the electrical environment, thereby reducing the potential for leakage into the human environment and creating additional trash in non-liner loads (televisions, computers, variable frequency drives, energy-efficient lighting, etc.).

 

The high frequency current (trash) on the neutral wire in the electrical system is positioned to return directly to the power system via the feeder neutral to the substation, and possibly beyond. However, as is often the case, the utility feeder neutral is not adequately sized (as required by the Public Service Commission of Wisconsin). If this is the case, much of the return current will flow through the ground rather than the feeder neutral. Under these conditions, the EMF FILTERS filters still provide benefits; this should be seen as local mitigation rather than part of a complete solution that requires an adequately sized neutral return.

 

At 60 Hz the filters act as capacitors and normally marginally improve the power factor of the customer load, which are normally slightly inductive.

 

Typical Home Installation

Filters are designed to be installed throughout the home in a pattern that corresponds to the distributed nature of the need. For example, installing two filters close to a desktop computer or a television is normally appropriate and effective. Installing filters, normally from two to six, close to the input power panel is recommended to address high frequency currents entering on the power lines. The total number of filters required depends on the size of the home, the amount of electrical equipment, and the quality of the power from the grid. Twenty filters are normally adequate for a “typical” house.

 

Installing an inadequate number of filters tends to result in overloaded filters, leading to an ineffective solution. The preferred installation method is to be guided by the EMF Microsurge Meter, which measures the amount of high frequency energy present. Readings of 30 or lower indicate an acceptable environment, while readings of 50 or higher indicate a need for additional filters. Readings between 30 and 50 are marginally acceptable, but should be reduced if anyone in the area is electrically sensitive.

 

The reader is encouraged to review the EMF Microsurge Meter Product Description, the EMF FILTERS filter installation instructions, and the EMF FILTERS Frequently Asked Questions

 

Filter Characteristics

  • 2 in. x 2 in. x 4 in.
  • Encased in an off-white plastic covering that fits naturally with home or office decor
  • Fits into a normal home or office electrical plug
  • Certified by Underwriters Laboratories and the Canadian Standards Association as safe for home and office use

 

Technical Information and Downloads:
Health Effects of EMF Health Effects

Contact:  Sales@PHDService.com

See our store for products and details.  Availability varies.  See many of our EMF Protection products at the online store.  Demand is high.  https://thebraincan.com/store-2/

 

is high.  https://thebraincan.com/store-2/

EMF Filter

EMF Filter Installation, Utilization, and Operation

EMFFix.com

EMF FILTERS – EMI Filters EMFFix.com

EMF/EMI FILTERS – For Home and Office

See our store for products and details.  Availability varies.  See many of our EMF Protection products at the online store.  Demand is high.  https://thebraincan.com/store-2/

 

Contact Info:

Office: 850-685-2353

email: sales@EMFFix.com

Email is the preferred means of contact so that we properly understand and address your questions.

 

Filter Installation Instructions

 

EMF FILTERS are very easy to install on your own. Follow these instructions to maximize filter effectiveness.

EMF Filter
EMF Filter

Note: Many homes may not have enough open outlets to install the number of filters needed to clean up the home. If this is the case, purchase several power strips, plug your electronic devices into them, and install filters in the power strips as per the instructions below.

 

One filter should be installed in power strips where each of the following electronic devices is located:

  • Hair Dryer
  • Mixer
  • Blender

 

Two filters should be installed in power strips where each of the following electronic devices is located:

  • Personal Computer
  • Laptop Computer
  • Inkjet Printer
  • Fax Machine
  • Personal/Home Office Copier
  • Entertainment Center (TV, VCR, DVD, Stereo, etc.)

 

Three filters should be installed in power strips where each of the following electronic devices is located:

  • Laser Printer
  • Large Office Copier

 

One filter should be installed in an outlet on each wall of the rooms you spend the most time in, especially bedrooms. Other rooms where this should be done may include your living room, kitchen, den, etc.

 

Two phases of current are used to supply utility power to your home: A phase and B phase. One filter should be installed in an outlet on each phase of current as close as possible to the main electrical panel in your home. Most homes will have one electrical outlet dropped down directly from the main panel; installing a filer in this outlet will take care of one current phase. For maximum effectiveness, call your local electrician and have him or her drop another outlet down from the panel on the other phase, then install a filter in that outlet as well.

 

When these directions are followed, a sufficient number of EMF FILTERS should be installed to effectively clean up the average home.

 

Filter Characteristics

  • 2 in. x 2 in. x 4 in.
  • Encased in an off-white plastic covering that fits naturally with home or office decor
  • Fits into a normal home or office electrical plug
  • Certified by Underwriters Laboratories and the Canadian Standards Association as safe for home and office use

 

Technical Information and Downloads:
Health Effects of EMF Health Effects

Contact:  Sales@PHDService.com

See our store for products and details.  Availability varies.  See many of our EMF Protection products at the online store.  Demand is high.  https://thebraincan.com/store-2/

EMF Filter

EMF Filters FAQ (Frequently Asked Questions) Dirty Electricity

EMF (ELECTROMAGNETIC FREQUENCY) FILTERS

EMF Filter
EMF Filter – EMI Filter

See our store for products and details.  Availability varies.  See many of our EMF Protection products at the online store.  Demand is high.  https://thebraincan.com/store-2/

EMF (ELECTROMAGNETIC FREQUENCY) FILTERS Filters – For Home and Office

Contact Info:

Office: 850-685-2353  (Ted Whidden)

email: Sales@EMFFix.com

Email contact preferred so that we adequately understand and respond to your questions.

 

Frequently Asked Questions

 

 

What are EMF (ELECTROMAGNETIC FREQUENCY FILTERS) Filters for?

EMF (ELECTROMAGNETIC FREQUENCY FILTERS) Filters remove or reduce high-frequency pollutants from the electrical wiring in your home or business.

 

How can I tell if I need EMF (ELECTROMAGNETIC FREQUENCY FILTERS) Filters?

If you and your neighbors have electronic equipment connected to electric outlets you need EMF (ELECTROMAGNETIC FREQUENCY FILTERS) Filters. The EMF (ELECTROMAGNETIC FREQUENCY) Microsurge meter can be used as an aid in determining exactly how many filters you may need.

 

How many EMF (ELECTROMAGNETIC FREQUENCY FILTERS) Filters do I need?

It usually takes 20 filters to effectively “clean up” the average home. Homes with more electronic equipment (i.e. computers, printers, fax machines, televisions) may require more filters. View our filter installation instructions for more information.

 

What is the lifespan of EMF (ELECTROMAGNETIC FREQUENCY FILTERS) Filters?

EMF (ELECTROMAGNETIC FREQUENCY FILTERS) Filters are not like oil filters that fill up with use. They are an electronic component, and should last a lifetime.

 

Do I need an electrician to install EMF (ELECTROMAGNETIC FREQUENCY FILTERS) Filters?

No. EMF (ELECTROMAGNETIC FREQUENCY FILTERS) Filters are designed so that anyone can properly install them. Simply plug the filters into an electrical outlet or power strip.

 

How do I install EMF (ELECTROMAGNETIC FREQUENCY FILTERS) Filters in my home?

View our filter installation instructions document for more information.

 

I plugged in a EMF (ELECTROMAGNETIC FREQUENCY FILTERS) Filter and there was a spark. Is this normal?

Yes, it is normal for the filters to spark when being plugged in. This should not hurt you, your electronic equipment, or the filters.

 

I plugged in a EMF (ELECTROMAGNETIC FREQUENCY FILTERS) Filter and it started humming. Should it do this?

No. When an EMF (ELECTROMAGNETIC FREQUENCY FILTERS) Filter is humming, it is overloaded. To resolved this problem, simply plug in more filters. Remember, it takes an average of 20 filters to clean up a home. One or two filters cannot do the work of twenty.

 

How can I tell if a EMF (ELECTROMAGNETIC FREQUENCY FILTERS) Filter is working?

The only way to tell if a EMF (ELECTROMAGNETIC FREQUENCY FILTERS) Filter is working is with the use of an oscilloscope or specially designed meter. However, many people claim they can tell the filters are working because they start to feel better.

Filter Characteristics

  • 2 in. x 2 in. x 4 in.
  • Encased in an off-white plastic covering that fits naturally with home or office decor
  • Fits into a normal home or office electrical plug
  • Certified by Underwriters Laboratories and the Canadian Standards Association as safe for home and office use
 

 

Technical Information and Downloads:
Health Effects of EMF Health Effects

Contact:  Sales@PHDService.com

See our store for products and details.  Availability varies.  See many of our EMF Protection products at the online store.  Demand is high.  https://thebraincan.com/store-2/

EMF Filter

EMFfix.com : EMF Filter to remove Dirty Electricity from your Home, School, or Office

WE HAVE BEEN A LEADER IN EMF METER SALES!

Once you get your EMF Metering Device (Stetzerizer Meter) from us, then plug it in to your wall.  If your reading is 80 or higher, then you could be in danger, GRAVE DANGER!  Our filters can reduce these harmful levels.  We are the price leader on filters as well.  You can purchase as many filters as you like from this site for only $28 each!  Get them NOW!

As indicated in U.S. Government testing and reports measures of electricity above 80 Graham-Stetzer units in an office, home, or work space can be hazardous to animals, people, and the environment.  Many of these stray current issues come from the power surges in your power grid, wall outlets, and electrical devices.  Our purpose designed filters can help remediate this problem.

It is simple really.  Get the meter, test your area.  Once the reading comes in, then use the filters to remediate the problem.  You can use the meter to test the area before and after the filters.  You can and will likely “feel” a difference, with fewer headaches, body pains, better sleep, etc.

We have much information on this.  We can choke a person in data, but what really needs to happen is you need to purchase filters and plug them in as you continue your efforts to lower the EMF effects of power surging through your body and work space.  Buy filters now at the lowest price online.

We are allowing folks to become affiiates in this business.  This could provide UNLIMITED Income Opportunity helping people avoid sickness!

EMF Filter
EMF Filter

See our store for products and details.  Availability varies.  See many of our EMF Protection products at the online store.  Demand is high.

In our modern world we have become entirely too dependent on WIFI, hotspots, and electrically stimulated devices.  These devices and the electromagnetic fields produced by them and by the systems that drive them cause abnormal issues in our world. Many of these have not been fully explained nor understood. Watch what happens………….

Electromagnetic Frequencies cause sickness and even cancers.  It is critical for people to see that “opposites attract” and “like or similar charges oppose”.  When cyclical electromagnetic pulses go through your walls, wires, and devices the signal that is sent out oscillates at 60 hertz (60 cycles per second).  Every “positive” charged part of the surge draws in or attracts the negative ions in your body.  Every negative surge repels.  Now look at this action of attraction and rejection occurring in your body at 60 cycles per second (60 Hertz).  This redirects electrical stimuli within the body causing or agitating a host of sickness issues.

For this reason we need EMF Protection.

 

EMF Protection comes in many forms.  There are “shields” for electromagnetic radiation protection, and there are filters.  Electromagnetic or EMF filters are available in several forms, yet they all are built on the foundational development and designs of our systems.

Our developers for Electromagnetic protection and Electromagnetic protection devices developed this science and the industry itself.

Our interest in EMF Filters, EMF Protection, and EMF devices stems in part from our ground breaking approaches to Holistic Cancer Treatment as outlined in our book, THE ANSWER TO CANCER: A SIMPLE SOLUTION TO THE WESTERN CONDITION.  Products and books in this regard are being made available through our online book store.

The recommended EMF Filters on our site are primarily of the Stetzer-Graham joint venture efforts.  The EMF Protection provided by these devices are readily measurable both mechanically using meters available through our web store. Many of the effects can be eliminated with the Stetzerizer filters available from our online store.

EMF Radiation protection is critical for those seeking good health.  No matter what approach or approaches you use, if you do not resolve the oscillating current effects mentioned above, then you will have the effects of a system out of alignment.  We are here to help.  Our goals are healing the body of pain and sickness.  Our holistic books and approaches are producing astounding results for those who are serious about solving their issues.  Our filter/meter products effectively reduce and/or eliminate EMF issues in your external environment. Our health approaches outlined in our books resolve EMF issues internal to the body. The combination is win-win-win.

In many instances pain and sickness leave the body by employing some simple methods.  We are so convinced that the combined approach will be universally successful that we are including a copy of our book in each and every order.

EMF Protection Reviews and EMF Protection Devices Reviews the world over recognize the Stetzerizer and Stetzer filters, meters and products.  The use of these and other by way of comparison in EMF protection reviews has the Stetzerizer products continually coming in at the top rating(s).  When combined with effective Electromagnetic Shielding and awareness approaches the results are immediate and astounding.

We encourage you to dig into the information provided in the links below regarding EMF/Electromagnetic testing, research and remediation.

Dirty Electricity is often driven by fluxuations in voltage/amperage in the lines and components within our homes.  This stray current can be “filtered” using patented processes and components.  We are pleased to represent the top producers in EMF reconciliation hardware.  EMF waves have been determined by U.S. Naval studies to cause sickness, cancers, and a host of problems.  EMF exists in every home in America due to computers, electronics, fluorescent lights, and a host of electronic gadgets.

We have a “plan” and a means to “test” the home/office, and two separate means to reconcile the environment.  We have one plan (a book/information) for reconciling the internal human body.  We have a product (filters/shock absorbers) that address the external environment including your office, bed room, home, etc.

Technical Information and Downloads:
Health Effects of EMF Health Effects

 

#EMF Protection, #EMF Protection Devices, #EMF Filter, #EMF Filters, #Electromagnetic Radiation Protection, #Electromagnetic Protection, #EMF Protection Reviews, #EMF Protection Devices Reviews, #Electromagnetic Shielding, #Stetzerizer, #Stetzerizer Filters, #Stetzer, #Graham-Stetzer,